TLC ENGINEERING / SPECIFY WITH CONTEXT
Interface, HBM, Straightpoint & FMS Replacement Review
Compare mechanical interfaces, rated force, calibration and signal compatibility before substituting an existing tension load cell.
A model reference starts the review; a drawing confirms the fit
| Reference family | TLC route to evaluate | Critical acceptance checks |
|---|---|---|
| Interface SM / SSM; Futek LSB302 / LSB352 | TLC-SBM | Thread diameter and pitch, installed height, force range, sensitivity and excitation |
| HBM / HBK S2M / S9M; Zemic H3; Celtron STC; Flintec model-specific | TLC-SBM review | Actual geometry, tension/compression calibration, sealing and temperature behaviour |
| Straightpoint / Crosby Radiolink Plus, Loadlink Plus / Wirelink; Dillon EDXtreme | TLC-LNK | WLL, proof load, minimum breaking load, pin fit, clearance and wireless protocol |
| FMS RMGZ; Montalvo / Dover Flexo sensor references; Honigmann RFS | TLC-WEB | Single-ended mounting, force direction, roller dimensions, moments and signal scaling |
| Tractel Dynasafe / Dynarope fixed-installation references; Sensy 5500 / Dinacell OMEGA, model-specific | TLC-ROP assessment | Actual permanent-mounting suitability, rope diameter/construction, calibration and alarm interface; no assumed structural interchangeability |
These are comparison routes, not verified interchangeability statements. Different variants within one series can use different threads, ratings and signals. Existing proprietary wireless receivers should not be assumed compatible.
HBM Z6 is a bending-beam reference, not an S-beam family match. Route it by its actual mounting geometry and force direction. For a load cell hook or hydraulic tensioning load cell request, send the complete force path and installation drawing for a separate feasibility review.
CMGZ309 belongs to controller review, separately from RMGZ force sensors. WTSTL belongs to Interface reference review. Permanent rope comparisons must establish fixed-installation suitability; portable quick-clamp inspection devices are outside this catalogue.
Build a model-to-model interface record
| Record field | Existing device | TLC proposal acceptance |
|---|---|---|
| Total height / width / clearance | Current drawing and revision | Approved proposed drawing; no assumed dimensional equality |
| Thread diameter, pitch and depth | Complete metric / UNF callout and usable engagement | Thread and assembly clearance checked together |
| 2.0 / 3.0 mV/V and excitation | Actual calibration sensitivity and supply | Gain, span, zero and bridge supply compatible |
| Four-wire / six-wire pinout | E+, E−, S+, S−, optional Sense+/Sense− and shield | Pin assignment verified from both documents; cable colours are not assumed universal |
| Calibration and mechanical evidence | Direction, uncertainty, environment and load ratings | Documented acceptance scope; original certification does not transfer |
Send these six items for a replacement assessment
- Full manufacturer part number and revision.
- Dimensioned mounting drawing and complete thread callouts.
- Rated force, operating direction and actual maximum / dynamic load.
- Electrical pinout, excitation, sensitivity or digital protocol.
- Required calibration, environmental and application approvals.
- Quantity, destination and required delivery date.
Any proposed substitute requires application validation. An original model's certificate, accuracy rating or safety factor does not transfer to a replacement.
Third-party names identify reference products only. TLC Tensile Metrology has no implied affiliation or endorsement.
Submit a part number for review →Carry the interface and evidence into your RFQ
Download the force-selection guide and editable interface worksheet.
Calibration and proof-load scope →Identify which report and accreditation scope the application requires.
Compare enquiry configurations →Filter the geometry, force envelope and signal before requesting a model.
CONFIGURATION / INTERFACE / DELIVERY
Send an engineering RFQ with the details intact
Choose the force path, signal and matching accessories. Include the destination so the quotation can confirm the product, calibration, freight and requested delivery term together.
[email protected]Open engineering notes are available in the downloads centre. Approved model STEP, IODD and real calibration reports are supplied against the selected configuration. Price, availability, lead time and warranty terms are confirmed in the formal quote.