Skip to content
AXIAL FORCE · PROOF LOAD · CONTINUOUS TENSION [email protected]
TLC↕TENSILE
METROLOGYRequest a quote ↗

APPLICATION / INTERFACE / EVIDENCE

Stainless Marine & Stage Rigging Load Links

Marine exposure and stage suspension create different requirements. Review stainless material, immersion conditions, wireless placement and stage-specific mechanical evidence separately.

Review the configuration and documents →
Stainless Marine & Stage Rigging Load Links engineering process schematic
ENGINEERING SCHEMATIC · NOT A MODEL DRAWING OR TEST RECORD

TLC-WTSTL / MARINE EXPOSURE

Separate corrosion, immersion and radio placement

For stainless marine load-link requests, define the material grade, salt exposure, immersion depth/duration and maintenance access. A stated IP code needs its exact test conditions; it is not a universal subsea qualification.

Interface WTSTL is a reference product identity. A TLC proposal requires its own drawing and evidence. If a radio path crosses water or steel shielding, review antenna placement or a suitable cabled architecture.

TLC-LNK-STG / STAGE SUSPENSION

Low visibility does not replace mechanical evidence

A black finish addresses appearance. Specify working load, minimum breaking-load requirement, duty, suspension arrangement and the loss-of-signal response separately.

If a 10:1 design factor is required by the project, request corresponding model and complete-assembly evidence. Reducing an indicated working load alone does not establish certification.

Put these conditions on the rigging enquiry

  • Working, dynamic and proof-test loads, expressed separately.
  • Shackle pin diameter, jaw clearance, permitted force direction and any centering hardware.
  • Radio region, receiver compatibility, update rate, power and communication-loss response.
  • Required report issuer, serial traceability and actual application approvals.

Hazardous-area use requires a separately qualified configuration. No ATEX, immersion, stage or complete-machine approval is implied by a configuration name.

Review the general load-link measurement chain →

CONFIGURATION AND DOCUMENT REVIEW

Compare the load path and signal before the drawing review

Enquiry references — final nominal rating and dimensions require approved model documentation
Configuration referenceForce / use envelopeSignal requestMechanical and evidence checksEnquiry
TLC-WTSTL

Stainless marine link review

5–100 metric tf requested scopeWireless handheld kit / 4–20 mA / RS485 ModbusShackle interfaces and material/environment review

Confirm 316L material, sealing, immersion conditions and antenna location; do not assume radio transmission through water.

Dimensions, accuracy and model datasheet: confirm on the approved configuration.		Request TLC-WTSTL review →
TLC-LNK-STG

Low-visibility stage link review

0.5–5 metric tf requested scopeWireless handheld kitSuspension geometry / finish review

Specify required minimum breaking load, finish and applicable approvals; a reduced WLL is not certification.

Dimensions, accuracy and model datasheet: confirm on the approved configuration.		Request TLC-LNK-STG review →

Resolve the configuration before the purchase order

Does stainless construction establish an underwater radio rating?

No. Material, immersion sealing and the radio path are separate requirements. Define depth, duration, media and antenna placement, and request the relevant model evidence.

Does a lower working load automatically prove a stage safety factor?

No. The required factor needs documented minimum breaking load and an approved complete load path, with applicable use and test requirements.

Carry the interface and evidence into your RFQ

Open engineering notes →

Download the force-selection guide and editable interface worksheet.

Calibration and proof-load scope →

Identify which report and accreditation scope the application requires.

Compare enquiry configurations →

Filter the geometry, force envelope and signal before requesting a model.

Replacing an existing sensor? Start with the sourced manufacturer reference and document checklist →

CONFIGURATION / INTERFACE / DELIVERY

Send an engineering RFQ with the details intact

Choose the force path, signal and matching accessories. Include the destination so the quotation can confirm the product, calibration, freight and requested delivery term together.

[email protected]

Open engineering notes are available in the downloads centre. Approved model STEP, IODD and real calibration reports are supplied against the selected configuration. Price, availability, lead time and warranty terms are confirmed in the formal quote.

1 / Contact
2 / Sensor geometry and configuration
Add installation and operating details (optional)

Share what you know for Stainless Marine / Black Stage Load Link. Leave an item blank or write “unknown” if it needs review.

6 / Hardware & calibration requests

Options are quotation requests. The final assembly rating and documentation scope require model-specific confirmation.

8 / Quantity & delivery country

TLC Tensile Metrology uses these details to respond to your enquiry. Privacy policy.

Review or select the complete RFQ text

The web form sends text. To include a drawing, datasheet or photograph, attach it in your email client and send to [email protected]. Selecting, copying or downloading a draft does not submit it. This form does not save a draft in browser storage.